How To Install A Kegerator Under Counter

Instead of installing a libation equally an attachment to your bar, you may want to consider installing an undercounter kegerator. These are ordinarily marketed to frat boys, but as a abode entertainer, one might come in handy in your own home.

The only problem is that installation can go tough. If you need a picayune help with your nether counter kegerator, read on to discover installation tips that may make the process easier.

Installation Guide

Even if you have the instructions from your kegerator, they may be difficult to follow or a little unclear. Follow this installation guide for some help.

Withal, continue in mind that depending on your kegerator make, brand and model, you may take to brand some slight alterations to the process we have here to piece of work for your specific kegerator.

Begin with the Wheels

As you lot get started, first make sure that you lot've removed everything from within the keg, including the keg floor. Advisedly tip the keg dispenser on its side and screw in the casters with the washers, making sure that everything is screwed in tight and is stable.

Set it back up direct once you're finished.

Installing the Tower

Begin by removing the plug to open up a space for the two. When yous open the door, yous'll be able to put your mitt underneath the top of the plug. Push until it comes out, or just employ something like a screwdriver to pry it open.

At this signal, you accept a space to install the draft tower. Unravel the beer hose line and feed it through the hole and into the tower itself. Once the line is all the fashion through, you can place the belfry in.

Alight the black adapter on the bottom of the tower to the hole in the chiffonier and turn it clockwise to lock it in place. Y'all'll but take to turn it around 25 degrees, and then don't twist too hard Now when you expect, the faucet connection will at present face the forepart of the cabinet.

If it doesn't, it's easy enough to twist and remove it so that yous can install it from some other position.

Installing Under the Counter

When y'all're installing the belfry, you'll want to do this in one case you take the hole drilled into your countertop. Your kegerator should come with a tower spacer to help you out when you're done putting it together properly.

This volition prevent the loss of cooling which occurs due to gaps betwixt the top of the kegerator and the bottom of the countertop.

Brand sure that the hole drilled into your countertop is lined up right with the hole at the top of the kegerator before you tighten the lock band to keep it stable and flush with the countertop.

Add in the Details

Now that you have the faucet in in that location and the wheels at the bottom, you can install the handle faucet. Choice upwards the blackness faucet handle and screw it but the faucet. So, screw the faucet onto the adapter on the front of the tower.

It should be vertical with the black handle that faces the ceiling and screwed on tightly. With that set, put the plastic drip tray below the faucet atop the counter.

Connecting Your Lines

Information technology's now time to connect your tube to the regulator. Get-go, y'all have to check on the switch below the main body to be sure the CO2 regulator shut off valve is closed and is perpendicular to the tubing.

Then, grab the CO2 line and install it on the regulator by attaching one end into the hose barb connectedness on the regulator. Secure it with a cocky-locking ruby-red plastic snap-on clamp and take hold of a pair of pliers to crimp the clamp as tightly as yous can.

Simply exist sure the clamp doesn't impede the valve. Finally, you lot only have to remove the black rubber plug from the back of the kegerator and feed the residual of the unused line through the tubing through the hole.

When yous're sure your CO2 cylinder is total and closed, adhere the regulator to the cylinder past screwing in the loose nut into the valve. Tighten it with a wrench or pliers before you mount the cylinder holder.

Just friction match upward the holes on the dorsum of the cabinet and slide the holder downwardly to lock it. The CO2 regulator should be in a position for you to read the numbers on the estimate and exist able to take hold of the shut off valve easily.

Connecting to the Keg

Brand sure the black pull handle of the keg coupler is airtight as you insert the keg coupler into the beer keg. Plow information technology some other 25 degrees to secure it to the keg. Now, attach the other terminate of the CO2 tube to the keg coupler and secure it with your other plastic snap-on clamp.

Secure this i tightly likewise. The beer line has to be connected from the belfry to the keg coupler as well. Merely insert the washer into the beer line hex nut, remove the protective rubber cap on the keg coupler and screw everything in properly.

Now, you only have to tap the keg past pulling the tap handle out. Push it down until it locks and you hear a click.

Calibration

In order for your kegerator to work correct, you'll want to calibrate the regulator. This tin be a complicated process. However, you actually only take to open up the valve to the gas cylinder, loosen the adjustment nut and gear up the pressure to 12 PSI past turning the regulator aligning screw.

You should hear the keg pressurizing equally you open the shut-off valve on the regulator. Allow the gas to vent past pulling the pressure relief valve briefly, which will requite you a more accurate reading.

Keep checking and rechecking the output pressure on the regulator until you have the right force per unit area. Put your keg in safely and you're good to brainstorm enjoying a nice beer!

Under Counter Kegerator Benefits

When kegerators are marketed towards higher frat boys, why might you desire one in your home? Beyond the fact that yous'll look similar a master when yous entertain, there are a few other advantages to installing a kegerator.

Lower Cost

Buying and setting upwardly a kegerator under the counter is a lot less expensive than ownership a cooler that's fastened to your bar. Over time, you can finish up saving a lot of money by setting up 1.

Lower Maintenance

The tap lines are brusk between the keg and the kegerator, pregnant that cleaning the lines are very easy. Longer lines will require weekly cleanings and will need more insulation to continue everything cool and to be sure they don't wear out over fourth dimension.

Improved Temperature Controls

Past doing an under counter kegerator installation, you'll be able to go on your beer at the best temperature possible. Whatever kind of beer can be kept at the right temperature for serving by using an individual kegerator.

Installing an under counter kegerator may testify difficult with the unlike screws and lines yous take to run through it to exist sure that it works properly. However, worry not, since yous now take all the steps needed to get yours gear up upwardly and working.

You may be able to practice them in a different lodge if it works amend for you, or may demand to make some adjustments depending on your model. But when you're all done, you'll be able to sit downwards and relax with a overnice beer.

Source: https://kegers.com/the-guide-to-undercounter-kegerator-installation/

Posted by: hoytjusbabyes.blogspot.com

Share this post